AC Fan

Termination Type : Plug

Blower Type : Tangential

Internal Diameter : 60 mm

Dimensions in mm: 60

AirFlow in m³/h: 70

Nominal Voltage in V: 230

Frequency in Hz: 50

Type of Voltage: AC

– Cable exit: Variable
– Terminal box design: Electrical connection via terminal strip
– Protection class: I

Mounting position Any
Condensate discharge holes None
Operation mode S1
Motor bearing Ball bearing
Touch current acc. IEC 60990
(measuring network Fig. 4, TN
system)
< 0.75 mA
Motor protection Thermal overload protector (TOP) wired internally
Cable exit Variable
Protection class I (if protective earth is connected by customer)
Product conforming to standard EN 60335-1; CE
Approval CCC; EAC

Installation position Any
Condensation
drainage holes
On rotor and stator sides
Mode S1
Motor bearing Ball bearing
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
<= 3.5 mA
Electrical hookup Terminal box
Motor protection Thermal overload protector (TOP) with
basic insulation
with cable Axial
Protection class I (with customer connection of protective
earth)
Conformity with
standards
EN 60034-1 (2010); CE
Approval EAC; VDE

Measurement category A
Efficiency category Static
Variable speed drive No
Specific ratio* 1.00

Material of blades Press-fitted sheet steel blank, sprayed with PP plastic
Material of guard grille Steel, phosphated and coated in black plastic
Motor protection Thermal overload protector (TOP) brought out
Product conforming to
standard
CE; EN 61800-5-1
Surface of rotor Cast in aluminium
Number of blades 5
Type of protection IP 54
Protection class I
Max. permissible ambient
motor temp. (transp./ storage)
+ 80 °C
Min. permissible ambient
motor temp. (transp./storage)
– 40 °C
Approval CSA C22.2 Nr.100; GOST; UL 1004-1; VDE

Installation position Shaft horizontal or rotor on bottom; rotor on top on request
Condensation drainage holes On rotor side
Mode S1
Motor bearing Ball bearing
Touch current according to IEC
60990 (measuring circuit Fig. 4,
TN system)
< 0.75 mA
Electrical hookup Via terminal box, capacitor integrated and connected
Motor protection Thermal overload protector (TOP) internally connected
With cable Variable
Protection class I (with customer connection of protective earth)
Motor capacitor according to EN
60252-1 in safety protection class
P0/S0
Conformity with standards EN 60335-1; CE

Installation position Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
drainage holes
On rotor side
Mode S1
Motor bearing Ball bearing
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
< 0.75 mA
with cable Variable
Protection class I (with customer connection of protective
earth)
Conformity with
standards
EN 60335-1, motor does not have
factory-installed overheating protection; CE
Approval EAC; CCC

Surface of rotor Coated in black
Number of blades 7
Type of protection IP 22; Depending on installation and position
Protection class I (if earth wire is connected by customer)
Max. permissible ambient
motor temp. (transp./ storage)
+ 80 °C
Min. permissible ambient
motor temp. (transp./storage)
– 40 °C
Approval CCC; CSA C22.2 Nr.113; GOST; UL 507; VDE

Surface of rotor Coated in black
Number of blades 7
Type of protection IP 42
Technical features – Control input 0-10 VDC / PWM
– Tach output
– Motor current limit
– Soft start
Max. permissible ambient
motor temp. (transp./ storage)
+80 °C
Min. permissible ambient
motor temp. (transp./storage)
-40 °C
Approval CCC; CSA C22.2 Nr.77; UL 1004-1; VDE

Mounting position Any
Condensate discharge holes None
Operation mode S1
Motor bearing Ball bearing
Technical features – Tach output
– Motor current limit
– Soft start
– Control input 0-10 VDC / PWM
EMC interference immunity Acc. to EN 61000-6-2 (industrial environment)
EMC interference emission Acc. to EN 55022 (Class B)
Electrical leads Via terminal strip
Motor protection Reverse polarity and locked-rotor protection
Product conforming to standard EN 60335-1
Approval UL 1004-1; EAC; CSA C22.2 No.77